Morpho | Premium Aluminim Case


The Nexus Morpho is a premium aluminium case without compromises. The best aluminium, with the best treatment and a great design. This ATX/Micro-ATX case is fully constructed out of the finest aluminium and is assembled taking the greatest care. We have done our utmost to get every little detail right.
Pure Nexus craftsmanship!

When we decided to design the Morpho smaller than any other usual computer case but we kept in mind not to hold back on the design of the outside and off course the layout of the inside. We wanted to have the best possible layout for the parts and the airflow must be optimal. We have used 2.0mm thick aluminum.

Case size: 40.2(L)cm x 20.3(w)cm x 37cm(h)
Case size: 15.84(L)inch x 8(w)inch x 14.58inch(h)

>click image to enlarge

Buttons with a quality touch. The buttons are made of the same quality aluminum as the case. We choose to use the same color and quality as the case so they completely blend in and give an extra touch of quality.

The LED's are nicely embedded in the front of the Morpho case. The LED's with a very nice red color, gives a superior visibility, but without being to bright, just right.

>click image to enlarge

The airflow has been thought thru carefully. The Morpho can be equipped with two 120mm case fans (supplied with the case). The front fan getting in the cool air and directly thru the Hard Disk bay and over the motherboard. While the rear fan blows the hot air out of the case. And the PSU (not supplied) adding just a bit extra to the airflow.

>click image to enlarge

The Nexus Morpho has a mirror finish logo badge on the rear of the chasis.

>click image to enlarge

The small size of the Nexus Morpho does not mean you have to give in on possibilities. The Morpho still has 5 PCI slots and therefore gives a lot of possibilities to build a computer with premium parts.

>click image to enlarge

The case has been designed so that the front case fan can get in the cool air very easily, thru two openings in the bottom of the case. The cool air is been forced thru the fan filter and is blown thru the hard disk tray which hold the hard disks.

>click image to enlarge

With most pc cases the exhaust fan is installed directly onto the rear panel, causing the hot air to bounce on the case and back to the case fan fan. This in general will produce noise and can decrease the lifetime of the exhaust fan. To solve this we keep a small gap between the case and the exhaust fan.

>click image to enlarge

>click to enlarge	With most smaller cases you often have to choose a "standard' ATX PSU. We included a special bracket so you will still be able to install the somewhat bigger PSUs (such as the Nexus 80 Plus series).	>click to enlarge	The 3.5" drive bay can be used for a FDD or a card reader. The bay can be removed completely and the drive can be installed outside the case to prevent scratches.
>click to enlarge	The HDD mounter is installed on the bottom of the case. It can hold one HDD. If you only use one HDD you can remove the HDD drive bay to expand the free space inside the case.	>click to enlarge	In the HDD bay is place for a maximum of three HDD's. The bay is made out of 2.0mm aluminum which is superior in heat dissipation. Because it easily can be removed the installation of the HDD's are simple and easy
>click to enlarge	Although the case is small the layout has been carefully thought thru. For example it can easily fit a GeForce7800 GTX graphics card.	>click to enlarge	Because aluminum is very sensitive and you easy can damage or scratch the case. We designed the case so that installation of most parts can be done outside of the case.
>click to enlarge	Included with the case are four rubber feet. The feet are made out of silicone damping rubber which is also being used in the audio industry. The feet will absorb the vibrations and reduce the noise.	>click to enlarge	Supplied with the case are 14 thumbscrews. The thumbscrews make installation simple, when these are installed you do not need a screwdriver to open the case, remove the PSU or replace PCI cards.
	Two Nexus Real Silent 120mm case fans are supplied with the Morpho case. Check here for details on the fans.		8 silicone Fan Mounts are supplied with the Morpho case to install the 120mm case fans in a vibration and resonance free manner. Check here for details on the fans.

	5.25" drive bays (3-units)
	3.5" drive bays (2-units)
	power button, reset switch, power led, hdd led
	Front panel
	2x USB 2.0, audio ports, fire wire (1x)

	Top Cover
	PSU location
	Motherboard base plate
	3.5" drive bays (up to 2x 3.5" HDD)
	HDD drive bay (up to 3x 3.5" HDD)
	Front 120mm case fan
	Bottom Chassis
	HDD Mounter (fit 1x 3.5"HDD)

	PSU bracket (2 versions supplied)
	Expansion slots
	Nexus badge
	120mm exhaust case fan

Images